Boutique oil press press

There are many details that need to be paid attention to during the operation of boutique oil press presses, which are crucial for ensuring operational safety, improving production efficiency, and extending equipment life. The following is a detailed explanation of the details in the operation of the oil press press:

1、 Preparation before operation

1. Equipment inspection: Before operation, a comprehensive inspection of the boutique oil press press is required, including whether the oil tank, oil level, and oil gauge meet the specified standards, whether each component is intact, whether each handle is flexible, and whether the safety protection device is intact and reliable.
2. Lubrication system: Check and confirm whether the lubrication system is working properly, including the oil pump, filter screen, and oil circuit, to ensure that the equipment can receive good lubrication during operation.

3. Mold installation: The installation of the mold must be firm and reliable, and the contact points of the upper and lower dies must be wiped clean. The die guide shaft sleeve must not be exposed. At the same time, it is necessary to ensure that the upper and lower dies are parallel and perpendicular, the pressure plate is flat, and the pressure plate bolts are symmetrically tightened. In addition, the center of the punching force must coincide with the center of the punching pressure, and the maximum punching force must not exceed the rated pressure of the machine.

2、 Precautions during operation

1. Start and idle operation: Before starting the boutique oil press press, the emergency stop button should be turned on first, the oil pump should be started, and then the working mode should be selected. Select continuous or single run on the body panel and press the green start button with both hands. After starting, the equipment should be run empty first to check for any abnormal noises and leaks in the oil and gas pipelines. At the same time, lubricating oil should be added to each lubrication point.
2. Material feeding and retrieval: During the stamping process, specialized tools (such as pliers and hooks) should be used to feed and retrieve raw materials. It is strictly prohibited to feed or retrieve raw materials by hand. In addition, to prohibit interlayer feeding stamping, the second feeding can only be carried out after the previously punched parts or residual materials have been removed.
3. Mold adjustment: During the stamping process, if it is necessary to adjust the mold, the machine must be stopped and the power must be cut off first. It is strictly prohibited to correct the position of the die blank during the operation of the slider and after stepping on the foot or operating the handle.

4. Pay attention to abnormalities: During the operation, always pay attention to the operation of the equipment. If there are any abnormal sounds or oil and gas leaks, stop the machine immediately for inspection. At the same time, it is strictly prohibited to continue working when encountering impacts, automatic drops, or abnormal sounds.

3、 Closing work after operation

1. Shutdown and Power Cut off: After the operation is completed, the machine should be stopped first and all control handles (switches) should be placed in neutral (zero position), then the power should be cut off.
2. Cleaning and maintenance: Clean the workbench, remove the mold and perform cleaning and maintenance. At the same time, it is necessary to add oil to the lubrication system to ensure that the equipment can operate normally the next time it is used.

3. Inspection and recording: Check for any debris or safety hazards in the work area and record them. If there are any parts that need to be repaired or replaced, the maintenance personnel should be notified in a timely manner for handling.

4、 Safety operation standards

1. Wear protective equipment: When operating the boutique oil press press, it is necessary to wear protective equipment such as earplugs and safety helmets to ensure personal safety.
2. Prohibition of operating under the influence of alcohol: It is strictly prohibited to operate machine tools under the influence of alcohol and to smoke while operating.
3. Cooperation when two or more people are operating the oil press press: When two or more people are operating the oil press press at the same time, one person must be responsible for commanding to ensure coordinated and consistent operation. Adequate lighting is necessary for night work.
In summary, the details of punch operation involve multiple aspects such as preparation before operation, precautions during operation, finishing work after operation, and safety operation standards. Only by strictly following these requirements can the normal operation and personal safety of the punching machine be ensured.